Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Hickok model 600A resto
#19

I kinda had to put my tester resto on hold until I get my bench set up. I mentioned in another thread things took a detour, and my shop is becoming my sons room, so I am not going to tackle sneaking into that meter until I have my magnifying light and bench set up, some nice soothing music and lots of toothpicks Icon_biggrin .

Mike might have a point if that meter slams down to 0. May be time to check the cap on the meter. If it is a just a "fallback", that may be normal. I have been using this tester sitting on it's front so the meter doesn't stick. In that position, the meter needle "falls" back a lot harder then when I have it on it's back. I have another tester that I use some that I have to be careful when switching one of the controls because it likes to slam the needle. I had to figure out the best combination to minimize. Following the manual wasn't the best in this case. I'll have a thread on this also once I have my bench set up.

If I could find the place called "Somewhere", I could find "Anything" Icon_confused

Tim

Jesus cried out and said, "Whoever believes in me , believes not in me but in him who sent me" John 12:44


Messages In This Thread
Hickok model 600A resto - by TV MAN - 10-19-2014, 08:55 PM
RE: Hickok model 600A resto - by morzh - 10-19-2014, 10:39 PM
RE: Hickok model 600A resto - by tab10672 - 10-19-2014, 11:01 PM
RE: Hickok model 600A resto - by morzh - 10-20-2014, 09:35 AM
RE: Hickok model 600A resto - by John R - 10-20-2014, 11:39 AM
RE: Hickok model 600A resto - by thirtiesradio - 10-20-2014, 12:46 PM
RE: Hickok model 600A resto - by Alan Douglas - 10-20-2014, 07:29 PM
RE: Hickok model 600A resto - by TV MAN - 10-21-2014, 05:18 PM
RE: Hickok model 600A resto - by tab10672 - 10-21-2014, 06:29 PM
RE: Hickok model 600A resto - by thirtiesradio - 10-22-2014, 12:15 PM
RE: Hickok model 600A resto - by Phlogiston - 10-22-2014, 02:02 PM
RE: Hickok model 600A resto - by Alan Douglas - 10-22-2014, 05:09 PM
RE: Hickok model 600A resto - by TV MAN - 11-02-2014, 05:28 PM
RE: Hickok model 600A resto - by Mondial - 11-02-2014, 07:42 PM
RE: Hickok model 600A resto - by Alan Douglas - 11-03-2014, 04:18 PM
RE: Hickok model 600A resto - by wazz - 12-07-2014, 09:45 PM
RE: Hickok model 600A resto - by Alan Douglas - 12-09-2014, 09:22 PM
RE: Hickok model 600A resto - by morzh - 12-09-2014, 10:47 PM
RE: Hickok model 600A resto - by TV MAN - 12-11-2014, 11:36 AM
RE: Hickok model 600A resto - by Alan Douglas - 12-11-2014, 04:10 PM
RE: Hickok model 600A resto - by codefox1 - 01-03-2015, 12:14 PM
RE: Hickok model 600A resto - by morzh - 01-03-2015, 01:46 PM
RE: Hickok model 600A resto - by TV MAN - 01-12-2015, 09:15 PM
RE: Hickok model 600A resto - by John R - 01-13-2015, 02:33 PM
RE: Hickok model 600A resto - by TV MAN - 01-13-2015, 06:03 PM
RE: Hickok model 600A resto - by thirtiesradio - 01-14-2015, 01:07 AM
RE: Hickok model 600A resto - by TV MAN - 01-15-2015, 10:15 AM
RE: Hickok model 600A resto - by K7Sparky - 01-31-2015, 10:21 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
IF can wire size and Rubber mounts?
Renovated Radios do carry what you need. As for the voltage, a wire should be at least 300V-rated.morzh — 11:13 PM
12' Philco
Andre the Giant got 2" on Kareem :lol:morzh — 11:11 PM
IF can wire size and Rubber mounts?
Thanks for the info but I doubt that a hardware store would be carrying the proper tuner assembly support mountings for ...georgetownjohn — 10:38 PM
12' Philco
Perhaps Kareem Abdul Jabbar?GarySP — 10:33 PM
My last cabinet for this year
Outstanding work, Dan! Take care and BE HEALTHY! GaryGarySP — 10:31 PM
My last cabinet for this year
They are a nice looking radio, Stromberg. I have a small tabletop octagon-dial one. It sounds surprisingly nice. And t...morzh — 09:40 PM
Philco 41-608 changer coupler
Different years but the same idea.morzh — 09:38 PM
My last cabinet for this year
That’s a beauty! :thumbup:klondike98 — 09:24 PM
Philco 41-608 changer coupler
Hi Morzh, I've searched using Mondial as the user name with various keywords such as 'coupler', 'motor', 'idler', 'p...alangard — 08:31 PM
Philco 16B Parts
I think the chassis is painted.morzh — 08:13 PM

[-]
Who's Online
There are currently 5271 online users. [Complete List]
» 1 Member(s) | 5270 Guest(s)
Avatar

>