Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Knobs for 46-1226
#5

Thanks!

He's been playing it for a long time.  I don't know how long he's had it.  I tried to explain it may need re-capping.

(12-19-2014, 11:10 AM)tab10672 Wrote:  I wouldn't even plug it in without atleast replacing the filter caps, although all the caps should be replaced before prolonged operation.

You should also check/replace resistors as needed and check voltages against the schematic.


Messages In This Thread
Knobs for 46-1226 - by jhgrahamjr - 12-19-2014, 09:58 AM
RE: Knobs for 46-1226 - by tab10672 - 12-19-2014, 11:10 AM
RE: Knobs for 46-1226 - by jhgrahamjr - 12-21-2014, 06:57 PM
RE: Knobs for 46-1226 - by Marsupial - 12-19-2014, 02:52 PM
RE: Knobs for 46-1226 - by jhgrahamjr - 12-21-2014, 06:58 PM
RE: Knobs for 46-1226 - by klondike98 - 12-19-2014, 04:52 PM
RE: Knobs for 46-1226 - by jhgrahamjr - 12-21-2014, 06:59 PM
RE: Knobs for 46-1226 - by klondike98 - 12-21-2014, 10:30 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1753 online users. [Complete List]
» 1 Member(s) | 1752 Guest(s)
Avatar

>