1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
40-165 Alignment adapter
klondike98
Phorum Moderator
******
Posts: 5,163
Threads: 273
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#16

01-04-2015, 05:25 PM
Icon_clap Icon_clap Icon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
40-165 Alignment adapter - by keith49vj3 - 12-31-2014, 12:47 PM
RE: 40-165 Alignment adapter - by klondike98 - 12-31-2014, 03:18 PM
RE: 40-165 Alignment adapter - by Nick3092 - 12-31-2014, 03:23 PM
RE: 40-165 Alignment adapter - by keith49vj3 - 12-31-2014, 05:11 PM
RE: 40-165 Alignment adapter - by klondike98 - 12-31-2014, 05:26 PM
RE: 40-165 Alignment adapter - by keith49vj3 - 12-31-2014, 06:12 PM
RE: 40-165 Alignment adapter - by klondike98 - 12-31-2014, 08:32 PM
RE: 40-165 Alignment adapter - by keith49vj3 - 01-01-2015, 08:20 AM
RE: 40-165 Alignment adapter - by codefox1 - 01-01-2015, 11:58 AM
RE: 40-165 Alignment adapter - by keith49vj3 - 01-01-2015, 01:04 PM
RE: 40-165 Alignment adapter - by keith49vj3 - 01-01-2015, 03:34 PM
RE: 40-165 Alignment adapter - by klondike98 - 01-01-2015, 03:44 PM
RE: 40-165 Alignment adapter - by Ron Ramirez - 01-01-2015, 05:03 PM
RE: 40-165 Alignment adapter - by keith49vj3 - 01-04-2015, 05:02 PM
RE: 40-165 Alignment adapter - by codefox1 - 01-04-2015, 05:11 PM
RE: 40-165 Alignment adapter - by klondike98 - 01-04-2015, 05:25 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Hello MrFixr55, Thank you for taking the time to explain. I measured 50 volts where you say. Today the 370 volts at ...dconant — 12:51 PM
462ron
Oh that sucks. It’s something easily overlooked. Hopefully it’s nothing more than a resistor! Ron462ron — 08:08 AM
Philco 46-480 Electronic Restoration
Just confirmed that you are correct. It’s the function generator. I connected the signal output probe to one of the inpu...jrblasde — 07:52 AM
Philco 46-480 Electronic Restoration
Ouch, you may be right. Yes, it is solid state. It’s the signal output of my oscilloscope. May be time to crack that ...jrblasde — 07:27 AM
462ron
If you didn’t put a DC blocking cap between the signal generator probe and the plate of the 1st IF it’s possible you ble...462ron — 07:07 AM
My Philco 37-116 Restore
Hi DConnant, The reason why C127 is isolated from ground is because sets of this vintage did not have the center tap...MrFixr55 — 01:07 AM
Philco 46-480 Electronic Restoration
The shield is on the 6H6. It was, in fact, a missing jumper to connect the main chassis ground to the RF chassis grou...jrblasde — 10:58 PM
Zenith H725
When dealing with noise on power lines, time to get my Jackery 240 out. Talk about clean can hold a portable am radio ne...David — 08:52 PM
Zenith H725
Arran - I bet you're right probably vinyl, there was no rubber smell when desoldering it, which you often get with the o...EdHolland — 08:23 PM
Zenith H725
Ed; It was very likely vinyl covered wire given the vintage of the set, there was some rubber/gutta percha wire used ...Arran — 06:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration