Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help on a GE Musiphonic
#4

It lives. I could write an obsolete book on how to not make a radio, and this model would be mentioned in every chapter. There is good sensitity and resaonable selectivity but the mutt of a printed circuit and point to point wiring make it a nightmare to work on. Jury's still out whether the buried capacitors in the IF cans are OK. Don't know how to get the cans off without a chainsaw. Cabinet responded well to brasso, and now shines like a "I an see my whiskers." Now what. does sanyone want it? Will burn it in a few more hours then it's off the bench and on to the shelr.


Messages In This Thread
Help on a GE Musiphonic - by codefox1 - 12-18-2008, 01:57 AM
Re: Help on a GE Musiphonic - by rghines1 - 12-18-2008, 09:16 AM
Re: Help on a GE Musiphonic - by codefox1 - 12-18-2008, 06:15 PM
Re: Help on a GE Musiphonic - by codefox1 - 12-27-2008, 06:28 PM
Re: Help on a GE Musiphonic - by rghines1 - 12-29-2008, 08:21 PM
Re: Help on a GE Musiphonic - by codefox1 - 12-31-2008, 12:48 PM
Re: Help on a GE Musiphonic - by Jim Berg - 01-04-2009, 01:03 AM
Re: Help on a GE Musiphonic - by Texasrocker - 01-04-2009, 10:51 PM
Re: Help on a GE Musiphonic - by Arran - 01-05-2009, 10:33 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>