RESTORING ZENITH 39A (CABINET FINISHED)

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RESTORING ZENITH 39A (CABINET FINISHED)

Fred Taylor
Phorum Expert

Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX

02-02-2015, 07:28 PM

(02-02-2015, 09:45 AM)klondike98 Wrote: Thanks Fred! Very helpful. What is the putty knife scaping off?

In that picture I am stripping the old finish, the stripper and old finish is what in scraping off, going with the grain make sure there are no burrs on the edge of putty knife or you can scratch the wood.

Find

« Next Oldest | Next Newest »

Messages In This Thread

RESTORING ZENITH 39A (CABINET FINISHED) - by Fred Taylor - 02-01-2015, 11:50 PM

RE:Console Cabinet RESTORING ZENITH 39A - by Fred Taylor - 02-01-2015, 11:56 PM

RE: RESTORING ZENITH 39A - by klondike98 - 02-02-2015, 09:45 AM

RE: RESTORING ZENITH 39A - by Fred Taylor - 02-02-2015, 07:28 PM

RE: RESTORING ZENITH 39A - by klondike98 - 02-02-2015, 07:38 PM

RE: RESTORING ZENITH 39A - by Fred Taylor - 02-02-2015, 08:04 PM

RE:CABINET RESTORING ZENITH 39A - by Fred Taylor - 02-03-2015, 08:50 PM

RE: RESTORING ZENITH 39A - by KCMike - 02-03-2015, 09:17 PM

RE: RESTORING ZENITH 39A - by Alan Douglas - 02-04-2015, 05:33 PM

RE: RESTORING ZENITH 39A - by Fred Taylor - 02-04-2015, 08:37 PM

RE: RESTORING ZENITH 39A - by Arran - 02-05-2015, 01:19 AM

RE: RESTORING ZENITH 39A - by sam - 02-05-2015, 05:15 AM

RE: RESTORING ZENITH 39A - by Arran - 02-07-2015, 02:21 AM

RE: RESTORING ZENITH 39A - by TimC - 02-06-2015, 05:41 PM

RE: RESTORING ZENITH 39A(FINISHED) - by Fred Taylor - 02-08-2015, 12:09 AM

RE: RESTORING ZENITH 39A (CABINET FINISHED) - by Fred Taylor - 02-08-2015, 04:28 PM

RE: RESTORING ZENITH 39A (CABINET FINISHED) - by Geoff - 02-18-2015, 04:06 PM

RE: RESTORING ZENITH 39A (CABINET FINISHED) - by Eliot Ness - 02-18-2015, 06:21 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me