1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 41-240 Deaf on Shortwave
canerods
Junior Member
**
Posts: 26
Threads: 3
Joined: Aug 2008
#8

12-30-2008, 06:05 PM
Chuck:
Yes, it's in the bandswitch! If I switch it back n' forth many times... then all of sudden the SW band comes alive -- I even got WWV at 10 mhz with a short 18" wire connected to the antenna jack. When I switch it back to broadcast, I lose the SW again. I've checked all those contact leaves, they seem OK. I guess the good news is you helped me isolate the problem... many thanks! Icon_smile
Joe
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 41-240 Deaf on Shortwave - by canerods - 12-28-2008, 05:47 PM
Re: Philco 41-240 Deaf on Shortwave - by exray - 12-29-2008, 08:14 AM
Re: Philco 41-240 Deaf on Shortwave - by canerods - 12-29-2008, 08:35 PM
Re: Philco 41-240 Deaf on Shortwave - by canerods - 12-30-2008, 10:50 AM
Re: Philco 41-240 Deaf on Shortwave - by canerods - 12-30-2008, 06:05 PM
Re: Philco 41-240 Deaf on Shortwave - by canerods - 01-01-2009, 04:57 PM
Re: Philco 41-240 Deaf on Shortwave - by exray - 01-01-2009, 06:40 PM
Re: Philco 41-240 Deaf on Shortwave - by codefox1 - 01-02-2009, 06:41 PM
Re: Philco 41-240 Deaf on Shortwave - by canerods - 01-02-2009, 08:31 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration