new here !!

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

new here !!

jefferz940
Junior Member

Posts: 9
Threads: 1
Joined: Feb 2015
City: Toronto, ON, CA

#12

02-13-2015, 10:55 AM

thanks guys! i will inspect the wires and test.... who knows it might still work as it sits? other than that i was surprised to see how plain jane it is back there in the chassis just a bunch of tubes/capacitors and well a battery pack spot.... if i needed all new tubes and such how much would they cost me to replace everything back there? plus a battery pack?

Find

« Next Oldest | Next Newest »

Messages In This Thread

new here !! - by jefferz940 - 02-12-2015, 04:37 PM

RE: new here !! - by morzh - 02-12-2015, 04:46 PM

RE: new here !! - by jefferz940 - 02-12-2015, 04:52 PM

RE: new here !! - by morzh - 02-12-2015, 04:57 PM

RE: new here !! - by jefferz940 - 02-12-2015, 05:08 PM

RE: new here !! - by klondike98 - 02-12-2015, 05:22 PM

RE: new here !! - by KCMike - 02-12-2015, 06:36 PM

RE: new here !! - by jefferz940 - 02-12-2015, 10:13 PM

RE: new here !! - by jefferz940 - 02-12-2015, 11:28 PM

RE: new here !! - by Arran - 02-13-2015, 12:25 AM

RE: new here !! - by sam - 02-13-2015, 05:11 AM

RE: new here !! - by jefferz940 - 02-13-2015, 10:55 AM

RE: new here !! - by klondike98 - 02-13-2015, 11:17 AM

RE: new here !! - by jefferz940 - 02-13-2015, 03:44 PM

RE: new here !! - by klondike98 - 02-13-2015, 05:07 PM

RE: new here !! - by PhilcoJohn - 02-13-2015, 08:07 PM

RE: new here !! - by jefferz940 - 02-13-2015, 08:41 PM

View a Printable Version

Users browsing this thread: 9 Guest(s)

Recent Posts
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help. I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran , Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me