Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

610 help
#6

(03-07-2015, 12:39 PM)Ron Ramirez Wrote:  34-2064 is a type 44 lamp.
http://www.philcorepairbench.com/lamps.htm

Model 610 is a 1936 model. Beginning with the 1935 season (June 1934), Philco introduced each new model year in June of the preceding calendar year, just as automobile manufacturers used to introduce new cars in September (and still do to some degree, but not always).

I would suggest buying the complete service information for this model from Chuck so that you can have the voltage charts, parts lists, and all known changes.
http://www.philcorepairbench.com/schematics.htm
Ron, thanks for the bulb info.  Tubes all test good.  I hooked up my signal generator to the grid cap of the 6A7 tube and I can pick up lots of stations by  changing the frequency on my generator.  I'm getting closer to figuring this one out.
Keith


Messages In This Thread
610 help - by keith49vj3 - 03-07-2015, 11:54 AM
RE: 610 help - by morzh - 03-07-2015, 12:17 PM
RE: 610 help - by keith49vj3 - 03-07-2015, 12:26 PM
RE: 610 help - by morzh - 03-07-2015, 12:34 PM
RE: 610 help - by Ron Ramirez - 03-07-2015, 12:39 PM
RE: 610 help - by keith49vj3 - 03-08-2015, 05:48 PM
RE: 610 help - by Ron Ramirez - 03-08-2015, 06:36 PM
RE: 610 help - by keith49vj3 - 03-08-2015, 07:45 PM
RE: 610 help - by morzh - 03-08-2015, 07:54 PM
RE: 610 help - by keith49vj3 - 03-08-2015, 08:44 PM
RE: 610 help - by morzh - 03-08-2015, 08:59 PM
RE: 610 help - by keith49vj3 - 03-09-2015, 06:08 AM
RE: 610 help - by morzh - 03-09-2015, 09:28 AM
RE: 610 help - by klondike98 - 03-09-2015, 09:52 AM
RE: 610 help - by Eliot Ness - 03-10-2015, 08:18 AM
RE: 610 help - by Mondial - 03-10-2015, 09:37 AM
RE: 610 help - by keith49vj3 - 03-12-2015, 06:31 AM
RE: 610 help - by morzh - 03-12-2015, 08:11 AM
RE: 610 help - by keith49vj3 - 03-13-2015, 06:26 AM
RE: 610 help - by Mondial - 03-13-2015, 07:41 AM
RE: 610 help - by keith49vj3 - 03-13-2015, 10:15 PM
RE: 610 help - by Mondial - 03-14-2015, 08:01 AM
RE: 610 help - by keith49vj3 - 03-14-2015, 03:05 PM
RE: 610 help - by Radioroslyn - 03-14-2015, 04:52 PM
RE: 610 help - by keith49vj3 - 03-14-2015, 06:09 PM
RE: 610 help - by Mondial - 03-14-2015, 06:21 PM
RE: 610 help - by morzh - 03-14-2015, 06:34 PM
RE: 610 help - by keith49vj3 - 03-14-2015, 07:09 PM
RE: 610 help - by Mondial - 03-14-2015, 07:23 PM
RE: 610 help - by Radioroslyn - 03-14-2015, 07:25 PM
RE: 610 help - by keith49vj3 - 03-14-2015, 07:59 PM
RE: 610 help - by Radioroslyn - 03-14-2015, 08:18 PM
RE: 610 help - by klondike98 - 03-14-2015, 09:10 PM
RE: 610 help - by Ron Ramirez - 03-14-2015, 10:13 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6154 online users. [Complete List]
» 2 Member(s) | 6152 Guest(s)
AvatarAvatar

>