Differences between 46-200 and 48-200

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Differences between 46-200 and 48-200

scooby214
Junior Member

Posts: 25
Threads: 3
Joined: Dec 2008

#20

01-10-2009, 07:45 PM

The back I ordered arrived from Retro-Tronics. Since I don't have the clips to hold it, I simply set it in the radio. It is a tight fit, but it fits and it looks great. The vents look the same as the ones I've seen on the original backs. It is made out of a smooth fiberboard panel and is thick enough to be flush with the back of the radio when installed. Of course, it doesn't have the stickers that one would find on the original back, but I do like the reproduction back panel.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Differences between 46-200 and 48-200 - by scooby214 - 01-01-2009, 04:12 PM

Re: Differences between 46-200 and 48-200 - by Ron Ramirez - 01-02-2009, 12:47 AM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-02-2009, 09:58 AM

Re: Differences between 46-200 and 48-200 - by Ron Ramirez - 01-02-2009, 11:36 AM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-02-2009, 11:51 AM

Re: Differences between 46-200 and 48-200 - by Ron Ramirez - 01-02-2009, 12:23 PM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-02-2009, 12:35 PM

Re: Differences between 46-200 and 48-200 - by Doug Houston - 01-02-2009, 04:32 PM

Re: Differences between 46-200 and 48-200 - by 49Stude63 - 01-02-2009, 10:17 PM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-02-2009, 11:01 PM

Re: Differences between 46-200 and 48-200 - by Ron Ramirez - 01-02-2009, 11:57 PM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-03-2009, 01:02 AM

Re: Differences between 46-200 and 48-200 - by BDM - 01-03-2009, 05:32 AM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-03-2009, 10:46 AM

Re: Differences between 46-200 and 48-200 - by 49Stude63 - 01-03-2009, 11:49 AM

Re: Differences between 46-200 and 48-200 - by Jim Berg - 01-04-2009, 12:39 AM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-04-2009, 07:41 PM

Re: Differences between 46-200 and 48-200 - by Jim Berg - 01-05-2009, 12:38 AM

Re: Differences between 46-200 and 48-200 - by Arran - 01-05-2009, 10:28 PM

Re: Differences between 46-200 and 48-200 - by scooby214 - 01-10-2009, 07:45 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help. I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran , Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM

Who's Online

There are currently 2877 online users. [Complete List]
» 3 Member(s) | 2874 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me