1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Identification? Philco?
nkladwig
New Member
*
Posts: 2
Threads: 1
Joined: Mar 2015
City: Oregon
#1
Question 

03-14-2015, 09:31 PM
Howdy Phorum - my wife picked up this asymmetric Philco radio with push buttons for me and I wanted to get it back in working condition. But what model is it? Dimensions are roughly 9.5" wide x 4.5" deep x 7" tall.

Inside on the right side there is a sticker that says "Part No 10602-A" pieces of the 02-A are missing so that is my best guess. And below that it says "Final Insp. " but the name or number is missing.

Attached are a few pics, thanks for your help!
   
   
   
   
Find
« Next Oldest | Next Newest »


Messages In This Thread
Identification? Philco? - by nkladwig - 03-14-2015, 09:31 PM
RE: Identification? Philco? - by shaler78 - 03-14-2015, 09:45 PM
RE: Identification? Philco? - by Ron Ramirez - 03-14-2015, 10:08 PM
RE: Identification? Philco? - by nkladwig - 03-15-2015, 10:26 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM

[-]
Who's Online
There are currently 5371 online users. [Complete List]
» 2 Member(s) | 5369 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios