1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco Knob & button cleaning
Jim Dutridge
Senior Member
****
Posts: 290
Threads: 54
Joined: Mar 2007
City: Toledo State, Province, Country: OH
#11

03-17-2015, 07:45 AM
That white (moldy?) stuff is likely caused by outgassing of the material. You can clean it off but it will eventually return. I don't thinik anyone has figured out a way to eliminate it yet.
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco Knob & button cleaning - by Pffester - 03-15-2015, 02:38 PM
RE: Philco Knob & button cleaning - by Warren - 03-15-2015, 03:18 PM
RE: Philco Knob & button cleaning - by klondike98 - 03-15-2015, 04:10 PM
RE: Philco Knob & button cleaning - by ekimetsok - 03-16-2015, 09:43 AM
RE: Philco Knob & button cleaning - by Pffester - 03-16-2015, 10:29 AM
RE: Philco Knob & button cleaning - by Eliot Ness - 03-16-2015, 11:00 AM
RE: Philco Knob & button cleaning - by Eric Adams - 03-16-2015, 07:56 PM
RE: Philco Knob & button cleaning - by Eric Adams - 03-16-2015, 10:26 PM
RE: Philco Knob & button cleaning - by Jim Dutridge - 03-17-2015, 07:45 AM
RE: Philco Knob & button cleaning - by Steve D - 03-17-2015, 08:39 AM
RE: Philco Knob & button cleaning - by Phlogiston - 03-17-2015, 10:59 AM
RE: Philco Knob & button cleaning - by Tony F - 03-26-2015, 02:31 PM
RE: Philco Knob & button cleaning - by klondike98 - 03-26-2015, 07:09 PM
RE: Philco Knob & button cleaning - by Arran - 04-02-2015, 11:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5685 online users. [Complete List]
» 1 Member(s) | 5684 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration