Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Model 20 escessive hum
#6

Yes, but if they are NOS caps then they are already old when you buy them and probably not reliable. You might check them to be sure. Your dealer could be reputable but NOS caps usually are not. It is usually recommended to not use NOS caps. Good Luck


Messages In This Thread
Philco Model 20 escessive hum - by Tubesforme - 03-25-2015, 03:52 PM
RE: Philco Model 20 escessive hum - by klondike98 - 03-25-2015, 04:17 PM
RE: Philco Model 20 escessive hum - by Mondial - 03-25-2015, 04:34 PM
RE: Philco Model 20 escessive hum - by Warren - 03-25-2015, 06:00 PM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-25-2015, 06:15 PM
RE: Philco Model 20 escessive hum - by Warren - 03-25-2015, 06:24 PM
RE: Philco Model 20 escessive hum - by Mondial - 03-25-2015, 07:02 PM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-25-2015, 09:09 PM
RE: Philco Model 20 escessive hum - by Arran - 03-27-2015, 12:01 AM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-30-2015, 12:11 PM
RE: Philco Model 20 escessive hum - by morzh - 03-27-2015, 08:52 AM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-27-2015, 03:25 PM
RE: Philco Model 20 escessive hum - by Mondial - 03-27-2015, 03:36 PM
RE: Philco Model 20 escessive hum - by morzh - 03-27-2015, 03:51 PM
RE: Philco Model 20 escessive hum - by radiohenry - 03-28-2015, 08:16 AM
RE: Philco Model 20 escessive hum - by morzh - 03-28-2015, 09:02 AM
RE: Philco Model 20 escessive hum - by radiohenry - 03-28-2015, 03:35 PM
RE: Philco Model 20 escessive hum - by klondike98 - 03-28-2015, 07:47 PM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-30-2015, 12:17 PM
RE: Philco Model 20 escessive hum - by radiohenry - 03-28-2015, 09:17 PM
RE: Philco Model 20 escessive hum - by morzh - 03-30-2015, 12:27 PM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-30-2015, 12:37 PM
RE: Philco Model 20 escessive hum - by morzh - 03-30-2015, 12:41 PM
RE: Philco Model 20 escessive hum - by morzh - 03-30-2015, 12:48 PM
RE: Philco Model 20 escessive hum - by codefox1 - 03-30-2015, 02:21 PM
RE: Philco Model 20 escessive hum - by Tubesforme - 03-31-2015, 02:14 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM

[-]
Who's Online
There are currently 3017 online users. [Complete List]
» 1 Member(s) | 3016 Guest(s)
Avatar

>