1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Push button switches on 40-190
mandh
Member
***
Posts: 73
Threads: 23
Joined: Aug 2008
#3

01-15-2009, 08:42 AM
I use a little Lubriplate for bearings and switch contacts. Leaves a thin film of lubricant on the switch/control that I think lasts longer than WD40. Product has been around for years.
Harv
Find
« Next Oldest | Next Newest »


Messages In This Thread
Push button switches on 40-190 - by Bob - 01-14-2009, 09:23 PM
Re: Push button switches on 40-190 - by mandh - 01-15-2009, 08:42 AM
Re: Push button switches on 40-190 - by scooby214 - 01-15-2009, 03:29 PM
Re: Push button switches on 40-190 - by Bob - 01-15-2009, 06:27 PM
Re: Push button switches on 40-190 - by scooby214 - 01-15-2009, 10:37 PM
Re: Push button switches on 40-190 - by Bob - 01-17-2009, 12:06 PM
Re: Push button switches on 40-190 - by BDM - 01-18-2009, 12:07 PM
Re: Push button switches on 40-190 - by scooby214 - 01-21-2009, 10:17 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5181 online users. [Complete List]
» 2 Member(s) | 5179 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration