Philco 41-105

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 41-105

Radioroslyn
Phorum Expert

Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#13

03-31-2015, 07:38 PM

You should send it to Sam he loves replacing rubber wire!! Ha Ha
Terry
Some of those smaller chassis can be a real pita to work on. A friend
gave me a little PT-61 to get work and he told me that he had
recapped it. Thinking this would be a quick job I got it home had
a look at it What didn't tell me is that in doing so he had knocked
off about half of the rubber insulation. It's a kwel set but a pita none
the less.
http://philcoradio.com/gallery/1940b.htm#u
Gud Lk w/ your's

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco 41-105 - by Jim Dutridge - 06-24-2014, 04:54 PM

RE: Philco 41-105 - by Arran - 06-25-2014, 02:38 AM

RE: Philco 41-105 - by Jim Dutridge - 06-25-2014, 09:13 AM

RE: Philco 41-105 - by jerryhawthorne - 06-25-2014, 01:08 PM

RE: Philco 41-105 - by TA Forbes - 06-25-2014, 01:28 PM

RE: Philco 41-105 - by Ron Ramirez - 06-26-2014, 05:55 PM

RE: Philco 41-105 - by Jim Dutridge - 03-30-2015, 05:38 PM

RE: Philco 41-105 - by Radioroslyn - 03-30-2015, 06:03 PM

RE: Philco 41-105 - by sam - 03-30-2015, 06:59 PM

RE: Philco 41-105 - by Radioroslyn - 03-30-2015, 07:43 PM

RE: Philco 41-105 - by sam - 03-31-2015, 03:52 AM

RE: Philco 41-105 - by Jim Dutridge - 03-31-2015, 04:50 PM

RE: Philco 41-105 - by Radioroslyn - 03-31-2015, 07:38 PM

RE: Philco 41-105 - by sam - 04-01-2015, 03:55 AM

RE: Philco 41-105 - by Ron Ramirez - 04-01-2015, 08:16 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help. I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran , Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM

Who's Online

There are currently 3447 online users. [Complete List]
» 2 Member(s) | 3445 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me