Need info: Stewart Warner 950

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Need info: Stewart Warner 950

BrendaAnnD
Phorum Expert

Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington

04-01-2015, 07:52 PM

I have a Stewart Warner 950 with no top cover. Also no tubes.

In looking up the schematics on N/A, I find several different versions of this set. This one appears to be a later model AC version. The AC version in the schematics uses 24A's for the RF amps, this one does not. Whatever it does use has no grid cap. Does anyone have any information on this version? The chassis seems to be in very good condition, and after installing an 80 rectifier, all sockets have voltages on the plates, so I really want to try to get this one going.

Thank you for your time.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Need info: Stewart Warner 950 - by BrendaAnnD - 04-01-2015, 07:52 PM

RE: Need info: Stewart Warner 950 - by Radioroslyn - 04-01-2015, 09:18 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-02-2015, 01:18 AM

RE: Need info: Stewart Warner 950 - by Radioroslyn - 04-02-2015, 07:30 AM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-02-2015, 09:34 AM

RE: Need info: Stewart Warner 950 - by Radioroslyn - 04-02-2015, 07:18 PM

RE: Need info: Stewart Warner 950 - by Ron Ramirez - 04-03-2015, 08:41 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-02-2015, 09:20 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-03-2015, 01:39 PM

RE: Need info: Stewart Warner 950 - by KCMike - 04-03-2015, 05:16 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-03-2015, 09:40 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-03-2015, 09:41 PM

RE: Need info: Stewart Warner 950 - by Radioroslyn - 04-03-2015, 09:53 PM

RE: Need info: Stewart Warner 950 - by BrendaAnnD - 04-03-2015, 11:10 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

Who's Online

There are currently 4524 online users. [Complete List]
» 2 Member(s) | 4522 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me