Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

One more Rogers console
#7

The dial is the same as the Rogers 10-12, but the tube count is only nine compared the 10-12 which has twelve.
It will be a while before I get to the cabinet, as we are getting about 4 inches of snow today.
I will post photos as I go along. someone has been in the chassis and did a bad job of soldering and the work is quit sloppy.. I have checked it over and fired it up and it picks up stations all across the dial, so everything is there and working. After the caps and the bias cell it should perform quite well.. All of my Rogers set have a very nice sound. The more I work on these Rogers sets the easier it gets


Messages In This Thread
One more Rogers console - by Dan Walker - 04-04-2015, 11:18 AM
RE: One more Rogers console - by morzh - 04-04-2015, 11:26 AM
RE: One more Rogers console - by Fred Taylor - 04-04-2015, 05:20 PM
RE: One more Rogers console - by jerryhawthorne - 04-04-2015, 05:34 PM
RE: One more Rogers console - by KCMike - 04-04-2015, 07:10 PM
RE: One more Rogers console - by PhilcoJohn - 04-04-2015, 07:50 PM
RE: One more Rogers console - by Dan Walker - 04-04-2015, 09:16 PM
RE: One more Rogers console - by jerryhawthorne - 04-05-2015, 01:29 AM
RE: One more Rogers console - by Dan Walker - 04-05-2015, 10:13 AM
RE: One more Rogers console - by PhilcoMike - 04-06-2015, 02:45 PM
RE: One more Rogers console - by jerryhawthorne - 04-06-2015, 03:14 PM
RE: One more Rogers console - by Dan Walker - 04-15-2015, 07:35 PM
RE: One more Rogers console - by Dan Walker - 05-04-2015, 11:56 PM
RE: One more Rogers console - by jerryhawthorne - 05-05-2015, 01:37 AM
RE: One more Rogers console - by sam - 05-05-2015, 03:28 AM
RE: One more Rogers console - by Arran - 05-06-2015, 10:49 PM
RE: One more Rogers console - by Dan Walker - 05-07-2015, 08:58 AM
RE: One more Rogers console - by Arran - 05-08-2015, 03:43 AM
RE: One more Rogers console - by Dan Walker - 05-30-2015, 10:13 PM
RE: One more Rogers console - by jerryhawthorne - 05-30-2015, 10:27 PM
RE: One more Rogers console - by Fred Taylor - 05-30-2015, 10:55 PM
RE: One more Rogers console - by PhilcoJohn - 05-31-2015, 07:56 AM
RE: One more Rogers console - by Dan Walker - 05-31-2015, 10:10 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>