1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
118H
AI2V
Member
***
Posts: 201
Threads: 26
Joined: Dec 2005
City: Morris Plains, NJ
#7

04-05-2015, 12:05 PM
Try stripping it with acetone and a green Scotch Brite pad; then wipe it down with denatured alcohol. You can use alcohol instead of acetone but it's a bit slower. Should take 45 minutes max.
Pete AI2V
Find
« Next Oldest | Next Newest »


Messages In This Thread
118H - by Jayce - 03-31-2015, 05:26 PM
RE: 118H - by KCMike - 03-31-2015, 07:16 PM
RE: 118H - by Jayce - 03-31-2015, 09:07 PM
RE: 118H - by Fred Taylor - 03-31-2015, 09:18 PM
RE: 118H - by Ron Ramirez - 04-01-2015, 08:21 AM
RE: 118H - by Eliot Ness - 04-01-2015, 08:23 AM
RE: 118H - by AI2V - 04-05-2015, 12:05 PM
RE: 118H - by PhilcoMike - 04-06-2015, 02:43 PM
RE: 118H - by KCMike - 04-09-2015, 09:30 PM
RE: 118H - by TA Forbes - 05-04-2015, 08:07 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM

[-]
Who's Online
There are currently 6063 online users. [Complete List]
» 1 Member(s) | 6062 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios