1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
philco 40-135 Static problem
David
Phorum Expert
*****
Posts: 1,191
Threads: 25
Joined: Jan 2014
City: Wellborn Florida
#7

04-05-2015, 08:13 PM
Have you cleaned the tube sockets? Take a real close look at the tuner for dirt or dust balls down deep, I like to use a flashlight and a hand lens. Good luck David 
Find
« Next Oldest | Next Newest »


Messages In This Thread
philco 40-135 Static problem - by Eric - 04-05-2015, 10:54 AM
RE: philco 40-135 Static problem - by Radioroslyn - 04-05-2015, 11:28 AM
RE: philco 40-135 Static problem - by Eric - 04-05-2015, 11:37 AM
RE: philco 40-135 Static problem - by Eric - 04-05-2015, 12:22 PM
RE: philco 40-135 Static problem - by Eric - 04-05-2015, 04:45 PM
RE: philco 40-135 Static problem - by Radioroslyn - 04-05-2015, 05:17 PM
RE: philco 40-135 Static problem - by David - 04-05-2015, 08:13 PM
RE: philco 40-135 Static problem - by Eric - 04-06-2015, 09:48 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5496 online users. [Complete List]
» 2 Member(s) | 5494 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration