Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 42-1012 Power up
#14

Skip,

It is difficult to just tell you what to do, as you are there and we are not.
I do not know your proficiency level with tubes, so until I (we) do, telling you "go there touch that" would be geopardizing your life.

If though you poke around more and tell us what gpyou see and measure, we will be able to help you a bit more.

When I say grid caps, well, if there are no caps there are still grids, so same technique applies except the. grid is a pin, it is close to other pin and touching it becomes more difficult.

Start with something. If you know what you are doing, touch those grids.
Measure some Voltages. You gotta start from somewhere.


PS. Do you have any equipment? I mean, other than a light bulb.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 42-1012 Power up - by vecher - 04-04-2015, 10:16 PM
RE: Philco 42-1012 Power up - by morzh - 04-04-2015, 10:38 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-04-2015, 10:52 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 05:21 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 05:42 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 06:01 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 06:31 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 08:43 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 09:34 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-05-2015, 11:08 PM
RE: Philco 42-1012 Power up - by vecher - 04-06-2015, 02:48 PM
RE: Philco 42-1012 Power up - by morzh - 04-06-2015, 02:56 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 11:39 AM
RE: Philco 42-1012 Power up - by morzh - 04-07-2015, 12:13 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 01:31 PM
RE: Philco 42-1012 Power up - by Chuck Schwark - 04-07-2015, 02:08 PM
RE: Philco 42-1012 Power up - by morzh - 04-07-2015, 02:57 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 03:15 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 08:50 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-07-2015, 09:00 PM
RE: Philco 42-1012 Power up - by vecher - 04-08-2015, 03:14 PM
RE: Philco 42-1012 Power up - by morzh - 04-08-2015, 03:16 PM
RE: Philco 42-1012 Power up - by vecher - 04-11-2015, 02:35 PM
RE: Philco 42-1012 Power up - by morzh - 04-11-2015, 02:46 PM
RE: Philco 42-1012 Power up - by vecher - 04-11-2015, 07:55 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-11-2015, 08:31 PM
RE: Philco 42-1012 Power up - by vecher - 04-12-2015, 10:13 PM
RE: Philco 42-1012 Power up - by morzh - 04-13-2015, 12:06 AM



Users browsing this thread: 8 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5514 online users. [Complete List]
» 2 Member(s) | 5512 Guest(s)
AvatarAvatar

>