1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-1012 Power up
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#21

04-08-2015, 03:14 PM
Does anyone know the best place to order tubes or where you ordered some. . I ordered my caps and 1 tube from tubesandmore. However the tube came bad. It was the XXFM/7X7 . showed shorted. They were nice and sent another tube but it also came bad. so looking for a better place.

Next I will attempt to do a alignment after I get better documentation on the way from Chuck Schwark.

I did notice that they want you to align in the cabinet. It that really necessary?

Skip...
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 42-1012 Power up - by vecher - 04-04-2015, 10:16 PM
RE: Philco 42-1012 Power up - by morzh - 04-04-2015, 10:38 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-04-2015, 10:52 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 05:21 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 05:42 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 06:01 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 06:31 PM
RE: Philco 42-1012 Power up - by morzh - 04-05-2015, 08:43 PM
RE: Philco 42-1012 Power up - by vecher - 04-05-2015, 09:34 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-05-2015, 11:08 PM
RE: Philco 42-1012 Power up - by vecher - 04-06-2015, 02:48 PM
RE: Philco 42-1012 Power up - by morzh - 04-06-2015, 02:56 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 11:39 AM
RE: Philco 42-1012 Power up - by morzh - 04-07-2015, 12:13 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 01:31 PM
RE: Philco 42-1012 Power up - by Chuck Schwark - 04-07-2015, 02:08 PM
RE: Philco 42-1012 Power up - by morzh - 04-07-2015, 02:57 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 03:15 PM
RE: Philco 42-1012 Power up - by vecher - 04-07-2015, 08:50 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-07-2015, 09:00 PM
RE: Philco 42-1012 Power up - by vecher - 04-08-2015, 03:14 PM
RE: Philco 42-1012 Power up - by morzh - 04-08-2015, 03:16 PM
RE: Philco 42-1012 Power up - by vecher - 04-11-2015, 02:35 PM
RE: Philco 42-1012 Power up - by morzh - 04-11-2015, 02:46 PM
RE: Philco 42-1012 Power up - by vecher - 04-11-2015, 07:55 PM
RE: Philco 42-1012 Power up - by Radioroslyn - 04-11-2015, 08:31 PM
RE: Philco 42-1012 Power up - by vecher - 04-12-2015, 10:13 PM
RE: Philco 42-1012 Power up - by morzh - 04-13-2015, 12:06 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5821 online users. [Complete List]
» 3 Member(s) | 5818 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration