1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
37-650 console
ptc4248
Junior Member
**
Posts: 7
Threads: 1
Joined: Jan 2015
City: Fitchburg MA
#1

04-09-2015, 07:50 PM
Hello Could anyone tell me what the plate voltage should be on the 6J5? Then what would the voltage be before and after resister #7 51k  ohms. The schematics I have do not show what it should be and I only have -1.25.  Then passes through resister #34 1m ohms to #7 resistor 51k and end result is approximately .200 to .300 millivolts not sure if this is correct.  Thank You  paul 
Find
« Next Oldest | Next Newest »


Messages In This Thread
37-650 console - by ptc4248 - 04-09-2015, 07:50 PM
RE: 37-650 console - by Radioroslyn - 04-10-2015, 03:21 PM
RE: 37-650 console - by ptc4248 - 04-10-2015, 05:19 PM
RE: 37-650 console - by Radioroslyn - 04-10-2015, 07:24 PM
RE: 37-650 console - by ptc4248 - 04-12-2015, 03:30 PM
RE: 37-650 console - by ptc4248 - 04-12-2015, 05:00 PM
RE: 37-650 console - by Radioroslyn - 04-13-2015, 06:00 AM
RE: 37-650 console - by ptc4248 - 04-13-2015, 08:50 AM
RE: 37-650 console - by Radioroslyn - 04-13-2015, 07:48 PM
RE: 37-650 console - by morzh - 04-13-2015, 07:53 PM
RE: 37-650 console - by ptc4248 - 04-13-2015, 08:55 PM
RE: 37-650 console - by ptc4248 - 04-16-2015, 08:27 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 4820 online users. [Complete List]
» 1 Member(s) | 4819 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration