1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
635 Tombstone
Warren
Senior Member
****
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
#3

04-12-2015, 10:02 PM
(04-12-2015, 07:06 PM)klondike98 Wrote:  Here's some info on Chuck's site that might help you out.  On another page, Chuck has some values listed with part numbers.  

Thanks Klondike... The pictures of the resistors might help. I have seen the resistor part number page but these part numbers are different. It doesn't show these. But, according to the pictures of resistors my 1 watt resistors should take care of pretty much most. I think the yellow one in the picture might be a 2 watt according to the pictures you showed. At least I know if im using the 1 watt it will take care of any but the biggest ones. Icon_smile
(This post was last modified: 04-12-2015, 10:04 PM by Warren.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
635 Tombstone - by Warren - 04-12-2015, 06:49 PM
RE: 635 Tombstone - by klondike98 - 04-12-2015, 07:06 PM
RE: 635 Tombstone - by Warren - 04-12-2015, 10:02 PM
RE: 635 Tombstone - by Warren - 04-20-2015, 02:19 AM
RE: 635 Tombstone - by Ron Ramirez - 04-20-2015, 07:11 AM
RE: 635 Tombstone - by Warren - 04-20-2015, 04:09 PM
RE: 635 Tombstone - by Warren - 04-22-2015, 11:41 PM
RE: 635 Tombstone - by Warren - 04-23-2015, 11:12 PM
RE: 635 Tombstone - by Steve Davis - 04-23-2015, 11:22 PM
RE: 635 Tombstone - by Warren - 04-25-2015, 12:52 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM
two videos to watch VHS and history of TV
Hello Every, Here are a couple videos right up my alley VHS and the history of Television . history of VCR VHS Hi...radiorich — 02:13 PM
Made mistake & did not label connection
You haven't given us the model number of the set so I looked up the 6A8 pin assignment. Pin 8 is the cathode and pin 7 i...RodB — 01:19 PM
Made mistake & did not label connection
Happy Thanksgiving all! I have made a real bonehead mistake this time. Hope someone can help.  I am trying to determi...georgetownjohn — 12:51 PM
New Philco Repair Bench
Apparently there is a new Philco Repair Bench found at https://philcoradio.com/repairbench/ When I try to go to order a ...dconant — 12:00 PM
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration