1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Push button switches on 40-190
scooby214
Junior Member
**
Posts: 25
Threads: 3
Joined: Dec 2008
#9

01-21-2009, 10:17 PM
Bob Wrote:Hello all
I was able to get some Lubriplate. I used it on the switch contacts and the tuner ball bearings. It make a big difference on the switches, they seam to work nice and easy and snap on/off real nice.
Thanks Again
Bob
Glad the Lubriplate worked for you! Icon_smile
Find
« Next Oldest | Next Newest »


Messages In This Thread
Push button switches on 40-190 - by Bob - 01-14-2009, 09:23 PM
Re: Push button switches on 40-190 - by mandh - 01-15-2009, 08:42 AM
Re: Push button switches on 40-190 - by scooby214 - 01-15-2009, 03:29 PM
Re: Push button switches on 40-190 - by Bob - 01-15-2009, 06:27 PM
Re: Push button switches on 40-190 - by scooby214 - 01-15-2009, 10:37 PM
Re: Push button switches on 40-190 - by Bob - 01-17-2009, 12:06 PM
Re: Push button switches on 40-190 - by BDM - 01-18-2009, 12:07 PM
Re: Push button switches on 40-190 - by scooby214 - 01-21-2009, 10:17 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently 6041 online users. [Complete List]
» 2 Member(s) | 6039 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration