Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Vernier shaft repair
#11

umm, have you ever considered contacting the shipping company responsible for your damaged item? Perhaps their $100. insurance ( UPS, Fedex, etc, type guaranteed automatic insurance coverage up to $110 value) on ANY item, vintage or not, would be acceptible to you? Might be worth consideration, as if you fillout the proper paperwork with shipping company, may yield you enough settlement $ to buy another similar Philco parts set chassis on ebay in the future? You will need a person from their insurance program to visually-inspect your item & the box it was shipped to you in. Just a idea! Icon_wink


Messages In This Thread
Vernier shaft repair - by dixierat - 01-19-2009, 09:48 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 05:10 AM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 08:14 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 09:35 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 10:19 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:03 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 11:35 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 11:40 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:54 PM
Re: Vernier shaft repair - by dixierat - 01-21-2009, 11:16 PM
Re: Vernier shaft repair - by Texasrocker - 01-22-2009, 12:30 AM
Re: Vernier shaft repair - by exray - 01-22-2009, 06:36 AM
Re: Vernier shaft repair - by dixierat - 01-22-2009, 08:43 PM
Re: Vernier shaft repair - by Texasrocker - 01-23-2009, 03:53 AM
Re: Vernier shaft repair - by dixierat - 01-23-2009, 10:03 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

[-]
Who's Online
There are currently 5567 online users. [Complete List]
» 1 Member(s) | 5566 Guest(s)
Avatar

>