1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Vernier shaft repair
exray
Phorum Expert
*****
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA State, Province, Country: PR
#12

01-22-2009, 06:36 AM
Ouch Curt,
Sounds like you are definitely in the market for a complete new shaft. Even if you hammer it all out even the slightest imperfections can turn into a noticeable 'bump' when tuning.
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Vernier shaft repair - by dixierat - 01-19-2009, 09:48 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 05:10 AM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 08:14 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 09:35 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 10:19 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:03 PM
Re: Vernier shaft repair - by dixierat - 01-20-2009, 11:35 PM
Re: Vernier shaft repair - by exray - 01-20-2009, 11:40 PM
Re: Vernier shaft repair - by BDM - 01-20-2009, 11:54 PM
Re: Vernier shaft repair - by dixierat - 01-21-2009, 11:16 PM
Re: Vernier shaft repair - by Texasrocker - 01-22-2009, 12:30 AM
Re: Vernier shaft repair - by exray - 01-22-2009, 06:36 AM
Re: Vernier shaft repair - by dixierat - 01-22-2009, 08:43 PM
Re: Vernier shaft repair - by Texasrocker - 01-23-2009, 03:53 AM
Re: Vernier shaft repair - by dixierat - 01-23-2009, 10:03 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5103 online users. [Complete List]
» 1 Member(s) | 5102 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration