38-12 power transformer

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-12 power transformer

morzh
Odobenus rosmarus

Posts: 15,819
Threads: 554
Joined: Oct 2011
City: Jackson, NJ

04-16-2015, 05:27 PM

The transformers will do for 38-15, 39-7, 39-6.
38-12 in a table mod uses small speaker and a small transformer, but the one from the chairside version will work fine except it will have to be maneuvered to go the small enclosure (possible, did it on mine).

I do not have voice coil impedance for these, but if you unsolder the secondary of the xfmr and measure (accounting for your meter leads' resistance) the Voice coil, then you could match it to 41 tube output and see whether the 125 SE has a tap that is close enough.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-12 power transformer - by ronlubke - 04-16-2015, 02:01 PM

RE: 38-12 power transformer - by klondike98 - 04-16-2015, 08:30 PM

RE: 38-12 power transformer - by Ron Ramirez - 04-16-2015, 09:06 PM

RE: 38-12 power transformer - by Arran - 04-16-2015, 11:27 PM

RE: 38-12 power transformer - by morzh - 04-17-2015, 03:09 PM

RE: 38-12 power transformer - by Ron Ramirez - 04-17-2015, 03:46 PM

RE: 38-12 power transformer - by ronlubke - 04-20-2015, 02:27 PM

RE: 38-12 power transformer - by ronlubke - 04-20-2015, 02:29 PM

RE: 38-12 power transformer - by morzh - 04-20-2015, 03:53 PM

RE: 38-12 power transformer - by ronlubke - 04-21-2015, 10:34 AM

RE: 38-12 power transformer - by morzh - 04-21-2015, 03:50 PM

RE: 38-12 power transformer - by ronlubke - 04-21-2015, 03:59 PM

RE: 38-12 power transformer - by morzh - 04-21-2015, 04:23 PM

RE: 38-12 power transformer - by ronlubke - 04-22-2015, 08:55 AM

RE: Advice for restoring 38-12 - by morzh - 04-16-2015, 05:27 PM

RE: Advice for restoring 38-12 - by klondike98 - 04-16-2015, 07:09 PM

RE: Advice for restoring 38-12 - by ronlubke - 04-16-2015, 07:15 PM

RE: Advice for restoring 38-12 - by ronlubke - 04-16-2015, 07:17 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM

Who's Online

There are currently 5282 online users. [Complete List]
» 1 Member(s) | 5281 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me