Vernier shaft repair

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Vernier shaft repair

dixierat
Junior Member

Posts: 49
Threads: 8
Joined: Nov 2008
City: Baton Rouge, LA

#13

01-22-2009, 08:43 PM

Wish I had thought about filing a claim earlier but the box has been trashed and the brass shaft straightened. It still has some eccentric rotation but may work until I can acquire a used part.Next step is to reassemble the parts. First attempt failed as pinion shaft would not slide into housing past the ball bearings because they rested onthe spring causing the bearings to jam against the housing.Will try again tomorrow. I have service bulletin 273; it describes how to take the drive apart but is a little weak on reassembly. It seems to me all 4 bearings must be aligned and the spring compressed to get the assembly into the housing.Any tips on how to do this will be greatly appreciated.
Curt

Find

« Next Oldest | Next Newest »

Messages In This Thread

Vernier shaft repair - by dixierat - 01-19-2009, 09:48 PM

Re: Vernier shaft repair - by exray - 01-20-2009, 05:10 AM

Re: Vernier shaft repair - by dixierat - 01-20-2009, 08:14 PM

Re: Vernier shaft repair - by BDM - 01-20-2009, 09:35 PM

Re: Vernier shaft repair - by dixierat - 01-20-2009, 10:19 PM

Re: Vernier shaft repair - by BDM - 01-20-2009, 11:03 PM

Re: Vernier shaft repair - by dixierat - 01-20-2009, 11:35 PM

Re: Vernier shaft repair - by exray - 01-20-2009, 11:40 PM

Re: Vernier shaft repair - by BDM - 01-20-2009, 11:54 PM

Re: Vernier shaft repair - by dixierat - 01-21-2009, 11:16 PM

Re: Vernier shaft repair - by Texasrocker - 01-22-2009, 12:30 AM

Re: Vernier shaft repair - by exray - 01-22-2009, 06:36 AM

Re: Vernier shaft repair - by dixierat - 01-22-2009, 08:43 PM

Re: Vernier shaft repair - by Texasrocker - 01-23-2009, 03:53 AM

Re: Vernier shaft repair - by dixierat - 01-23-2009, 10:03 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

Who's Online

There are currently 5382 online users. [Complete List]
» 1 Member(s) | 5381 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me