1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
speaker reconing
klondike98
Phorum Moderator
******
Posts: 5,071
Threads: 269
Joined: Nov 2012
City: Bandon State, Province, Country: OR
#11

04-17-2015, 08:52 AM
I bought 8" cones from Mat Electronics http://matelectronics.com/audio/speaker-...foam-edge/ .  They have some others as well.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
speaker reconing - by Tubesforme - 04-15-2015, 02:54 PM
RE: speaker reconing - by RodB - 04-15-2015, 03:33 PM
RE: speaker reconing - by Eric Adams - 04-15-2015, 05:16 PM
RE: speaker reconing - by Tubesforme - 04-15-2015, 09:20 PM
RE: speaker reconing - by Steve D - 04-16-2015, 07:33 AM
RE: speaker reconing - by jerryhawthorne - 04-16-2015, 03:27 PM
RE: speaker reconing - by Crist Rigotti - 04-16-2015, 08:07 PM
RE: speaker reconing - by jerryhawthorne - 04-16-2015, 11:38 PM
RE: speaker reconing - by Eliot Ness - 04-17-2015, 12:19 AM
RE: speaker reconing - by Crist Rigotti - 04-17-2015, 01:12 AM
RE: speaker reconing - by klondike98 - 04-17-2015, 08:52 AM
RE: speaker reconing - by jerryhawthorne - 04-17-2015, 11:01 AM
RE: speaker reconing - by Bob Andersen - 04-23-2015, 03:57 PM
RE: speaker reconing - by klondike98 - 04-23-2015, 04:37 PM
RE: speaker reconing - by jerryhawthorne - 04-23-2015, 04:50 PM
RE: speaker reconing - by Bob Andersen - 04-24-2015, 12:30 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 1051 online users. [Complete List]
» 1 Member(s) | 1050 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration