1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Need Help Identifying this Philco
RoyG
Member
***
Posts: 53
Threads: 20
Joined: May 2013
City: Portland, OR
#1

04-17-2015, 11:48 AM
I am headed to look at this one today. I did not see a similar cabinet in the gallery. The ID label is not quite clear enough to read. Partial shot of the chassis gives me the idea that it might be a 11 tube model 16 chassis. Any ideas?

               
(This post was last modified: 04-17-2015, 12:00 PM by RoyG.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Need Help Identifying this Philco - by RoyG - 04-17-2015, 11:48 AM
RE: Need Help Identifying this Philco - by RoyG - 04-17-2015, 12:01 PM
RE: Need Help Identifying this Philco - by RoyG - 04-17-2015, 07:24 PM
RE: Need Help Identifying this Philco - by Jayce - 04-17-2015, 08:54 PM
RE: Need Help Identifying this Philco - by RoyG - 04-17-2015, 10:11 PM
RE: Need Help Identifying this Philco - by Kestas - 04-26-2015, 11:21 AM



Users browsing this thread: 13 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM

[-]
Who's Online
There are currently 3593 online users. [Complete List]
» 2 Member(s) | 3591 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios