1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Speaker and tubes for a Knight radio
BrendaAnnD
Phorum Expert
*****
Posts: 1,108
Threads: 89
Joined: Jun 2011
City: Tacoma State, Province, Country: Washington
#25

04-21-2015, 08:35 PM
There's info on this radio: http://www.radiomuseum.org/r/allied_rad_..._sg_8.html

Also, to open up your speaker possibilities a bit, since this has a P-P output, you can use a P-P output transformer that works for 6K6's and then use any 4-32 ohm speaker you like.
Find
« Next Oldest | Next Newest »


Messages In This Thread
RE: Speaker for a Knight radio - by morzh - 02-14-2015, 12:45 PM
RE: Speaker for a Knight radio - by Eliot Ness - 02-14-2015, 03:47 PM
RE: Speaker for a Knight radio - by morzh - 02-14-2015, 05:59 PM
RE: Speaker for a Knight radio - by OldRestorer - 02-14-2015, 06:24 PM
RE: Speaker for a Knight radio - by Radioroslyn - 02-15-2015, 09:58 AM
RE: Speaker for a Knight radio - by OldRestorer - 02-15-2015, 11:28 AM
RE: Speaker for a Knight radio - by sam - 02-15-2015, 02:45 PM
RE: Speaker for a Knight radio - by OldRestorer - 02-15-2015, 03:40 PM
RE: Speaker for a Knight radio - by sam - 02-15-2015, 04:07 PM
RE: Speaker for a Knight radio - by klondike98 - 02-15-2015, 05:02 PM
RE: Speaker for a Knight radio - by OldRestorer - 02-15-2015, 05:08 PM
RE: Speaker and tubes for a Knight radio - by sam - 04-18-2015, 06:57 PM
RE: Speaker and tubes for a Knight radio - by BrendaAnnD - 04-21-2015, 08:35 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6027 online users. [Complete List]
» 1 Member(s) | 6026 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)