1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-22CL
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#7

04-23-2015, 09:56 PM
Phlogiston Wrote:Can I get it with an MP3 port and a mini-bar? Icon_lol

Icon_lolno

And Warren - thanks! Icon_biggrin

The clock movement is scheduled to arrive tomorrow and the dial covers on Saturday, so hopefully this weekend I'll have this set ready for K-town. Icon_thumbup

Hey, I forgot to mention something. This is an AC/DC chassis with a series filament string, and it uses a resistor in parallel with the dial lamp instead of a tap on the rectifier filament. Just for fun, I tried a 6 volt AC/DC bayonet base LED lamp in place of the 47 lamp. The LED worked! Icon_eek It did not dim as much as the 47 lamp does while the filaments warm up, and it worked well overall. Good to know! (I put a new #47 incandescent bulb back in after conducting the experiment.)
--
Ron Ramirez
Ferdinand IN
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 42-22CL - by Ron Ramirez - 04-22-2015, 09:50 PM
RE: Philco 42-22CL - by NostalgiaRadioTime - 04-22-2015, 10:23 PM
RE: Philco 42-22CL - by sam - 04-23-2015, 03:32 AM
RE: Philco 42-22CL - by Ron Ramirez - 04-23-2015, 06:21 AM
RE: Philco 42-22CL - by Warren - 04-23-2015, 07:23 PM
RE: Philco 42-22CL - by Phlogiston - 04-23-2015, 08:50 PM
RE: Philco 42-22CL - by Ron Ramirez - 04-23-2015, 09:56 PM
RE: Philco 42-22CL - by Eliot Ness - 04-24-2015, 11:30 AM
RE: Philco 42-22CL - by Ron Ramirez - 04-24-2015, 11:45 AM
RE: Philco 42-22CL - by Ron Ramirez - 04-28-2015, 05:13 PM
RE: Philco 42-22CL - by Ron Ramirez - 04-28-2015, 05:18 PM
RE: Philco 42-22CL - by klondike98 - 04-28-2015, 06:13 PM
RE: Philco 42-22CL - by sam - 04-28-2015, 11:19 PM
RE: Philco 42-22CL - by Eliot Ness - 04-28-2015, 11:23 PM
RE: Philco 42-22CL - by Chuck Schwark - 04-29-2015, 09:12 AM
RE: Philco 42-22CL - by Ron Ramirez - 05-01-2015, 08:08 PM
RE: Philco 42-22CL - by sam - 05-01-2015, 08:32 PM
RE: Philco 42-22CL - by morzh - 05-01-2015, 08:37 PM
RE: Philco 42-22CL - by Ron Ramirez - 05-01-2015, 08:52 PM
RE: Philco 42-22CL - by RON JACQUARD - 06-23-2015, 07:03 PM
RE: Philco 42-22CL - by Ron Ramirez - 06-23-2015, 08:12 PM
RE: Philco 42-22CL - by RON JACQUARD - 06-25-2015, 07:43 PM
RE: Philco 42-22CL - by Art Hoch - 07-15-2015, 04:48 PM
RE: Philco 42-22CL - by mikethedruid - 07-15-2015, 08:42 PM
RE: Philco 42-22CL - by Ron Ramirez - 07-15-2015, 09:55 PM
RE: Philco 42-22CL - by mikethedruid - 07-16-2015, 01:33 AM
RE: Philco 42-22CL - by sam - 07-16-2015, 04:11 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration