42-1008P ALigntment

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

42-1008P ALigntment

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

05-11-2015, 09:54 AM

I just had same thing happen on my 42-1012 see thread. Found that the Mica Caps around the Osc tube were way off in value. After replacement radio worked and aligned perfect. Also if you get same stations on 2 different frequencies about 1 Mhz apart (image) replacing the mica caps take care of that too.

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

42-1008P ALigntment - by Edisla - 05-10-2015, 11:58 PM

RE: 42-1008P ALigntment - by Warren - 05-11-2015, 12:07 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 09:54 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 10:43 AM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:29 AM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 01:25 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 09:56 PM

RE: 42-1008P ALigntment - by vecher - 05-11-2015, 11:31 PM

RE: 42-1008P ALigntment - by Edisla - 05-11-2015, 11:57 PM

RE: 42-1008P ALigntment - by Edisla - 05-12-2015, 12:48 AM

RE: 42-1008P ALigntment - by Nick3092 - 05-12-2015, 10:09 AM

RE: 42-1008P ALigntment - by vecher - 05-18-2015, 11:36 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 09:48 PM

RE: 42-1008P ALigntment - by Ron Ramirez - 05-20-2015, 09:59 PM

RE: 42-1008P ALigntment - by Edisla - 05-20-2015, 10:23 PM

RE: 42-1008P ALigntment - by vecher - 05-20-2015, 10:32 PM

RE: 42-1008P ALigntment - by Edisla - 05-21-2015, 11:41 AM

RE: 42-1008P ALigntment - by vecher - 05-21-2015, 09:18 PM

View a Printable Version

Users browsing this thread: 12 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me