Transitone 48 250 126

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Transitone 48 250 126

Paul Philco322
Super Moderator

Posts: 4,382
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts

05-16-2015, 05:25 PM

Set arrived today, in fine shape, labela intact, dial glass Ok but shows a tiny bit of flaking, original back, and service label from Carl's TV Radio Natick Ma.

A nice litttle set.

Paul

Tubetalk1

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Transitone 48 250 126 - by Paul Philco322 - 05-14-2015, 08:06 PM

RE: Transitone 48 250 126 - by codefox1 - 05-15-2015, 08:58 AM

RE: Transitone 48 250 126 - by Paul Philco322 - 05-15-2015, 10:10 PM

RE: Transitone 48 250 126 - by NostalgiaRadioTime - 05-15-2015, 10:54 PM

RE: Transitone 48 250 126 - by Paul Philco322 - 05-16-2015, 09:18 AM

RE: Transitone 48 250 126 - by Paul Philco322 - 05-16-2015, 05:25 PM

RE: Transitone 48 250 126 - by Paul Philco322 - 05-16-2015, 09:19 PM

RE: Transitone 48 250 126 - by Joe Rossi - 05-16-2015, 10:19 PM

RE: Transitone 48 250 126 - by NostalgiaRadioTime - 05-16-2015, 10:41 PM

View a Printable Version

Users browsing this thread: 6 Guest(s)

Recent Posts
Philco 60 Squealing
Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran , Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM

Who's Online

There are currently 3694 online users. [Complete List]
» 1 Member(s) | 3693 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me