1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 81 Front End Problem
Steve Davis
Phorum Expert
*****
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
#5

02-02-2009, 11:12 PM
Dr. Volts, Considering the fact that the problem occured after a period of non use, it could be the oscillator coil has absorbed some moisture. It may have to be removed and baked in the oven for a few minutes.
Steve
M R Radios   C M Tubes
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 81 Front End Problem - by Guest - 02-02-2009, 07:56 PM
Re: Philco 81 Front End Problem - by exray - 02-02-2009, 08:41 PM
Re: Philco 81 Front End Problem - by Guest - 02-02-2009, 10:00 PM
Re: Philco 81 Front End Problem - by exray - 02-02-2009, 10:45 PM
Re: Philco 81 Front End Problem - by Steve Davis - 02-02-2009, 11:12 PM
Re: Philco 81 Front End Problem - by Guest - 02-05-2009, 08:48 PM
Re: Philco 81 Front End Problem - by Guest - 02-06-2009, 06:45 PM
Re: Philco 81 Front End Problem - by exray - 02-06-2009, 07:01 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5517 online users. [Complete List]
» 1 Member(s) | 5516 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration