First Time Refinish

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

First Time Refinish - 39-6

Nick3092
Member

Posts: 126
Threads: 13
Joined: Sep 2013
City: Milwaukee, Wisconsin

05-21-2015, 06:41 PM

Well, I haven't gotten around to stripping the cabinet yet, but I just ran to the Mohawk distributor after work. I talked to him about the small chip. He told me I could use a light color of that epoxy to fill it, and a grain pen to blend it. I also noticed when I got home, I inadvertently got TONE FINISH TONER MEDIUM BROWN/AMERICAN WALNUT instead of just "medium walnut". Icon_mad

Any idea if that will still give good results, or should I run back tomorrow and exchange it? I really don't want to run back of it's not necessary as his limited hours require me to run out of work and drive in rush hour traffic both ways.

Find

« Next Oldest | Next Newest »

Messages In This Thread

First Time Refinish - 39-6 - by Nick3092 - 05-07-2015, 08:51 AM

RE: First Time Refinish - 39-6 - by klondike98 - 05-07-2015, 09:20 AM

RE: First Time Refinish - 39-6 - by OldRestorer - 05-07-2015, 11:30 AM

RE: First Time Refinish - 39-6 - by klondike98 - 05-07-2015, 12:13 PM

RE: First Time Refinish - 39-6 - by Nick3092 - 05-08-2015, 03:39 PM

RE: First Time Refinish - 39-6 - by Nick3092 - 05-12-2015, 10:12 AM

RE: First Time Refinish - 39-6 - by Ron Ramirez - 05-12-2015, 11:46 AM

RE: First Time Refinish - 39-6 - by Nick3092 - 05-12-2015, 04:38 PM

RE: First Time Refinish - 39-6 - by Nick3092 - 05-21-2015, 06:41 PM

RE: First Time Refinish - 39-6 - by OldRestorer - 05-21-2015, 08:13 PM

RE: First Time Refinish - 39-6 - by Nick3092 - 05-22-2015, 03:05 PM

RE: First Time Refinish - 39-6 - by OldRestorer - 05-23-2015, 10:17 PM

RE: First Time Refinish - 39-6 - by Nick3092 - 06-04-2015, 08:12 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online

There are currently 5600 online users. [Complete List]
» 1 Member(s) | 5599 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me