Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco Chassis Corrosion?
#14

Thanks, Arran

I really appreciate all the advice I'm getting. I'll certainly save all this assembled knowledge and experience. I'll have enough bench space cleared out pretty soon so I can make a start.

I don't think any of my oldies have been repaired or restored in the past. I'm sure the 41-255 and 42-1008 are all original. Probably the 36-610 and 38-93 also. It's probably geting harder to find old radios that haven't had some repair in the past, but in the late 60's, early 70's it wasn'y unusual at all to find 40's vintage sets that never had anything done except have some tubes replaced perhaps. Again, thanks, guys.

Mike


Messages In This Thread
Philco Chassis Corrosion? - by Michael Dennis - 02-02-2009, 02:52 PM
Re: Philco Chassis Corrosion? - by Ron Ramirez - 02-02-2009, 08:13 PM
Re: Philco Chassis Corrosion? - by 49Stude63 - 02-02-2009, 10:28 PM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-03-2009, 12:49 AM
Re: Philco Chassis Corrosion? - by BDM - 02-03-2009, 01:03 AM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-03-2009, 01:22 PM
Re: Philco Chassis Corrosion? - by Texasrocker - 02-04-2009, 12:00 AM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-04-2009, 12:11 AM
Re: Philco Chassis Corrosion? - by Texasrocker - 02-04-2009, 12:19 AM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-04-2009, 12:37 AM
Re: Philco Chassis Corrosion? - by Texasrocker - 02-04-2009, 03:12 AM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-04-2009, 04:49 AM
Re: Philco Chassis Corrosion? - by Arran - 02-05-2009, 06:03 PM
Re: Philco Chassis Corrosion? - by Michael Dennis - 02-05-2009, 07:08 PM
Re: Philco Chassis Corrosion? - by Texasrocker - 02-06-2009, 01:50 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4109 online users. [Complete List]
» 2 Member(s) | 4107 Guest(s)
AvatarAvatar

>