Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phonograph motor fried??
#8

odpilot
you checked and answered you own question

On the formerly restored 53-1750, I get 118 Volts coming into the phonograph motor.  On the new one I am restoring, voltmeter reads 1.5Volts coming into the switch
so check before switch. you have one to check against

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2


Messages In This Thread
Phonograph motor fried?? - by ODPILOT - 05-28-2015, 02:02 PM
RE: Phonograph motor fried?? - by Warren - 05-28-2015, 03:13 PM
RE: Phonograph motor fried?? - by ODPILOT - 05-30-2015, 09:10 AM
RE: Phonograph motor fried?? - by jerryhawthorne - 05-30-2015, 02:37 PM
RE: Phonograph motor fried?? - by ODPILOT - 06-01-2015, 11:49 AM
RE: Phonograph motor fried?? - by morzh - 06-01-2015, 11:58 AM
RE: Phonograph motor fried?? - by sam - 06-02-2015, 04:14 AM
RE: Phonograph motor fried?? - by ODPILOT - 06-02-2015, 12:19 PM
RE: Phonograph motor fried?? - by morzh - 06-02-2015, 01:13 PM
RE: Phonograph motor fried?? - by sam - 06-02-2015, 08:01 PM
RE: Phonograph motor fried?? - by morzh - 06-02-2015, 09:31 PM
RE: Phonograph motor fried?? - by sam - 06-03-2015, 04:35 AM
RE: Phonograph motor fried?? - by morzh - 06-03-2015, 09:20 AM
RE: Phonograph motor fried?? - by sam - 06-03-2015, 12:26 PM
RE: Phonograph motor fried?? - by morzh - 06-03-2015, 03:12 PM
RE: Phonograph motor fried?? - by jerryhawthorne - 06-03-2015, 03:45 PM
RE: Phonograph motor fried?? - by morzh - 06-03-2015, 03:58 PM
RE: Phonograph motor fried?? - by jerryhawthorne - 06-03-2015, 04:36 PM
RE: Phonograph motor fried?? - by sam - 06-03-2015, 07:17 PM
RE: Phonograph motor fried?? - by ODPILOT - 06-03-2015, 09:06 PM
RE: Phonograph motor fried?? - by sam - 06-04-2015, 03:46 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

[-]
Who's Online
There are currently 5363 online users. [Complete List]
» 1 Member(s) | 5362 Guest(s)
Avatar

>