1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Removing glued grill cloth??
Dan Walker
Senior Member
****
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
#1

06-10-2015, 11:55 PM
  I am finally getting to my rogers 10-12 and I find that the grill cloth is not attached to a board behind the grill.. It is glued to the grill  [around the edges].  On this radio ,the grill can't be removed. I need to take  off  the grill cloth so I can strip the cabinet.. any suggestions are welcome


Attached Files Image(s)
               
   Living in Calgary Alberta
Find
« Next Oldest | Next Newest »


Messages In This Thread
Removing glued grill cloth?? - by Dan Walker - 06-10-2015, 11:55 PM
RE: Removing glued grill cloth?? - by Arran - 06-11-2015, 12:19 AM
RE: Removing glued grill cloth?? - by Fred Taylor - 06-11-2015, 07:20 AM
RE: Removing glued grill cloth?? - by morzh - 06-11-2015, 08:41 AM
RE: Removing glued grill cloth?? - by Fred Taylor - 06-11-2015, 08:53 AM
RE: Removing glued grill cloth?? - by TimC - 06-11-2015, 09:37 AM
RE: Removing glued grill cloth?? - by Dan Walker - 06-11-2015, 09:51 AM
RE: Removing glued grill cloth?? - by Dan Walker - 06-11-2015, 02:47 PM
RE: Removing glued grill cloth?? - by TimC - 06-11-2015, 03:03 PM
RE: Removing glued grill cloth?? - by Fred Taylor - 06-11-2015, 08:07 PM
RE: Removing glued grill cloth?? - by Arran - 06-12-2015, 01:17 AM
RE: Removing glued grill cloth?? - by Dan Walker - 06-18-2015, 11:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

[-]
Who's Online
There are currently 2909 online users. [Complete List]
» 3 Member(s) | 2906 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)