Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 70A
#9

By all means get over there and give the owner a $50.00 before he sobers up and realizes what he's done!  What intrigues me is the word "special" stamped onto the back of the chassis.  Can anyone elaborate on that?  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
Philco 70A - by Crist Rigotti - 06-17-2015, 10:24 PM
RE: Philco 70A - by Phlogiston - 06-17-2015, 11:25 PM
RE: Philco 70A - by morzh - 06-18-2015, 08:41 AM
RE: Philco 70A - by Crist Rigotti - 06-18-2015, 08:47 AM
RE: Philco 70A - by Phlogiston - 06-18-2015, 09:38 AM
RE: Philco 70A - by Crist Rigotti - 06-18-2015, 09:41 AM
RE: Philco 70A - by Steve Davis - 06-18-2015, 11:25 AM
RE: Philco 70A - by Steve Davis - 06-18-2015, 11:31 AM
RE: Philco 70A - by GarySP - 06-18-2015, 11:52 AM
RE: Philco 70A - by TA Forbes - 06-18-2015, 12:03 PM
RE: Philco 70A - by Crist Rigotti - 06-18-2015, 01:34 PM
RE: Philco 70A - by Ron Ramirez - 06-18-2015, 04:53 PM
RE: Philco 70A - by Crist Rigotti - 06-18-2015, 07:25 PM
RE: Philco 70A - by Ron Ramirez - 06-18-2015, 07:51 PM
RE: Philco 70A - by morzh - 06-18-2015, 07:57 PM
RE: Philco 70A - by Crist Rigotti - 06-19-2015, 01:03 PM
RE: Philco 70A - by plymouthrod - 06-19-2015, 01:25 PM
RE: Philco 70A - by Crist Rigotti - 06-19-2015, 03:16 PM
RE: Philco 70A - by Ron Ramirez - 06-19-2015, 04:38 PM
RE: Philco 70A - by KCMike - 06-19-2015, 06:53 PM
RE: Philco 70A - by Crist Rigotti - 06-19-2015, 08:47 PM
RE: Philco 70A - by Ron Ramirez - 06-19-2015, 09:26 PM
RE: Philco 70A - by Arran - 06-19-2015, 09:36 PM
RE: Philco 70A - by Crist Rigotti - 06-19-2015, 09:41 PM
RE: Philco 70A - by Crist Rigotti - 06-19-2015, 10:21 PM
RE: Philco 70A - by KCMike - 06-20-2015, 12:51 PM
RE: Philco 70A - by Crist Rigotti - 06-20-2015, 06:51 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently 3984 online users. [Complete List]
» 1 Member(s) | 3983 Guest(s)
Avatar

>