Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

my "NEW" 37-630
#15

Hi, Lee ! Judging by the schematic, as I said before, when properly aligned, the radio should have very good selectivity and sensitivity because of the TRF stage in all three bands. Should be a real pleasure to use with a longwire antenna and decent ground, good for DX in general, on the BC band as well as SW, AM only of course, no SSB or CW. (To be honest I only have ready access to the schematic for the 37-620 handy, but the 630 is much the same except for the shadowmeter circuitry.) Order the right schematic from Chuck Schwark, you will be glad you did. A good clear schematic is the first place to start. But I am verging on "electronic restoration," so I'll leave any more for when you start a thread on this there.


Messages In This Thread
my "NEW" 37-630 - by NN7X - 06-24-2015, 08:55 PM
RE: my "NEW" 37-630 - by klondike98 - 06-24-2015, 09:29 PM
RE: my "NEW" 37-630 - by Crist Rigotti - 06-24-2015, 10:07 PM
RE: my "NEW" 37-630 - by mikethedruid - 06-24-2015, 10:09 PM
RE: my "NEW" 37-630 - by Crist Rigotti - 06-24-2015, 10:39 PM
RE: my "NEW" 37-630 - by morzh - 06-24-2015, 10:46 PM
RE: my "NEW" 37-630 - by OldRestorer - 06-24-2015, 10:52 PM
RE: my "NEW" 37-630 - by morzh - 06-24-2015, 11:01 PM
RE: my "NEW" 37-630 - by OldRestorer - 06-24-2015, 11:45 PM
RE: my "NEW" 37-630 - by sam - 06-25-2015, 04:45 AM
RE: my "NEW" 37-630 - by George Kirk - 06-25-2015, 11:37 AM
RE: my "NEW" 37-630 - by KCMike - 06-25-2015, 02:39 PM
RE: my "NEW" 37-630 - by NN7X - 06-25-2015, 07:34 PM
RE: my "NEW" 37-630 - by klondike98 - 06-25-2015, 07:43 PM
RE: my "NEW" 37-630 - by mikethedruid - 06-25-2015, 11:32 PM
RE: my "NEW" 37-630 - by GarySP - 06-26-2015, 03:01 PM
RE: my "NEW" 37-630 - by PAradiogeek - 06-26-2015, 07:36 PM
RE: my "NEW" 37-630 - by NN7X - 07-03-2015, 10:48 PM
RE: my "NEW" 37-630 - by Tom Hamilton - 07-03-2015, 05:27 PM
RE: my "NEW" 37-630 - by Paul Philco322 - 07-03-2015, 09:04 PM
RE: my "NEW" 37-630 - by NN7X - 07-03-2015, 10:36 PM
RE: my "NEW" 37-630 - by PhilcoJohn - 07-04-2015, 07:05 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture. dconant — 09:21 AM
American Bosch Model 802 auto radio
Hi Arran ,  Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM

[-]
Who's Online
There are currently 3095 online users. [Complete List]
» 2 Member(s) | 3093 Guest(s)
AvatarAvatar

>