Grunow 654

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Grunow 654

vecher
Phorum Expert

Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA

#18

06-26-2015, 03:57 PM

Ok, I removed the Cans.. Glad I did because the insulation was gone from one of wires..

[Image: http://i292.photobucket.com/albums/mm38/...mrtjji.jpg]

The wire going to the Grid cap was also frayed.. Did the 1st can already now will work on this one. Also found most of resistors have changed value.. The Mica caps were OK.. The dogbone resistors one that was 20K was reading 70K other was 5K reading 6.5 K..

So I will Keep moving Forward..

Skip...

Find

« Next Oldest | Next Newest »

Messages In This Thread

Grunow 654 - by vecher - 06-21-2015, 11:36 PM

RE: Grunow 654 - by Arran - 06-22-2015, 02:13 AM

RE: Grunow 654 - by Radioroslyn - 06-22-2015, 06:03 AM

RE: Grunow 654 - by vecher - 06-22-2015, 05:38 PM

RE: Grunow 654 - by vecher - 06-22-2015, 09:35 PM

RE: Grunow 654 - by Arran - 06-23-2015, 12:26 AM

RE: Grunow 654 - by Warren - 06-22-2015, 10:46 PM

RE: Grunow 654 - by jerryhawthorne - 06-22-2015, 11:17 PM

RE: Grunow 654 - by mikethedruid - 06-22-2015, 11:55 PM

RE: Grunow 654 - by vecher - 06-23-2015, 08:51 AM

RE: Grunow 654 - by vecher - 06-23-2015, 07:18 PM

RE: Grunow 654 - by Arran - 06-23-2015, 11:57 PM

RE: Grunow 654 - by codefox1 - 06-24-2015, 07:17 AM

RE: Grunow 654 - by vecher - 06-24-2015, 02:23 PM

RE: Grunow 654 - by Arran - 06-25-2015, 12:45 AM

RE: Grunow 654 - by jerryhawthorne - 06-24-2015, 02:50 PM

RE: Grunow 654 - by vecher - 06-24-2015, 03:14 PM

RE: Grunow 654 - by vecher - 06-26-2015, 03:57 PM

RE: Grunow 654 - by vecher - 07-04-2015, 03:52 PM

RE: Grunow 654 - by Radioroslyn - 07-04-2015, 04:58 PM

RE: Grunow 654 - by vecher - 07-04-2015, 07:57 PM

RE: Grunow 654 - by vecher - 07-04-2015, 10:37 PM

RE: Grunow 654 - by Arran - 07-05-2015, 01:12 AM

RE: Grunow 654 - by vecher - 07-05-2015, 09:51 PM

RE: Grunow 654 - by Arran - 07-06-2015, 02:06 AM

RE: Grunow 654 - by vecher - 07-06-2015, 09:05 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me