Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Grunow 654
#19

I tried to re-stuff the Caps on this.. However didn't go very well. So for now I just went with the right replacements under the chassis.. radio works very well. Performed alignment..

One question.. I did not replace the bias cell. How can you tell if its still working.. I pickup lots of stations on both bands and volume is load with no distortion..

Skip...


Messages In This Thread
Grunow 654 - by vecher - 06-21-2015, 11:36 PM
RE: Grunow 654 - by Arran - 06-22-2015, 02:13 AM
RE: Grunow 654 - by Radioroslyn - 06-22-2015, 06:03 AM
RE: Grunow 654 - by vecher - 06-22-2015, 05:38 PM
RE: Grunow 654 - by vecher - 06-22-2015, 09:35 PM
RE: Grunow 654 - by Arran - 06-23-2015, 12:26 AM
RE: Grunow 654 - by Warren - 06-22-2015, 10:46 PM
RE: Grunow 654 - by jerryhawthorne - 06-22-2015, 11:17 PM
RE: Grunow 654 - by mikethedruid - 06-22-2015, 11:55 PM
RE: Grunow 654 - by vecher - 06-23-2015, 08:51 AM
RE: Grunow 654 - by vecher - 06-23-2015, 07:18 PM
RE: Grunow 654 - by Arran - 06-23-2015, 11:57 PM
RE: Grunow 654 - by codefox1 - 06-24-2015, 07:17 AM
RE: Grunow 654 - by vecher - 06-24-2015, 02:23 PM
RE: Grunow 654 - by Arran - 06-25-2015, 12:45 AM
RE: Grunow 654 - by jerryhawthorne - 06-24-2015, 02:50 PM
RE: Grunow 654 - by vecher - 06-24-2015, 03:14 PM
RE: Grunow 654 - by vecher - 06-26-2015, 03:57 PM
RE: Grunow 654 - by vecher - 07-04-2015, 03:52 PM
RE: Grunow 654 - by Radioroslyn - 07-04-2015, 04:58 PM
RE: Grunow 654 - by vecher - 07-04-2015, 07:57 PM
RE: Grunow 654 - by vecher - 07-04-2015, 10:37 PM
RE: Grunow 654 - by Arran - 07-05-2015, 01:12 AM
RE: Grunow 654 - by vecher - 07-05-2015, 09:51 PM
RE: Grunow 654 - by Arran - 07-06-2015, 02:06 AM
RE: Grunow 654 - by vecher - 07-06-2015, 09:05 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>