Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

American Bosch 5AC
#17

Ok remove the 80 tube. Set meter to >500ac. Measure voltage from the ungrounded side of R-12 (should be a big resistor, wire comes from the power transformer) to pin 2 of the 80 socket and then pin 3 of the 80 socket. Should see about 300-350vac on pin 2 and then pin 3 should be the same. If that is OK check R-12 it may be open.

Terry


Messages In This Thread
American Bosch 5AC - by dseverson - 06-16-2015, 02:29 PM
RE: American Bosch 5AC - by dseverson - 06-16-2015, 02:31 PM
RE: American Bosch 5AC - by jerryhawthorne - 06-16-2015, 03:05 PM
RE: American Bosch 5AC - by dseverson - 06-16-2015, 03:09 PM
RE: American Bosch 5AC - by Radioroslyn - 06-16-2015, 05:37 PM
RE: American Bosch 5AC - by jerryhawthorne - 06-16-2015, 07:20 PM
RE: American Bosch 5AC - by Radioroslyn - 06-16-2015, 08:24 PM
RE: American Bosch 5AC - by dseverson - 06-16-2015, 09:40 PM
RE: American Bosch 5AC - by jerryhawthorne - 06-16-2015, 09:59 PM
RE: American Bosch 5AC - by dseverson - 06-16-2015, 10:56 PM
RE: American Bosch 5AC - by dseverson - 06-16-2015, 11:13 PM
RE: American Bosch 5AC - by Arran - 06-17-2015, 01:55 AM
RE: American Bosch 5AC - by dseverson - 06-18-2015, 09:02 PM
RE: American Bosch 5AC - by dseverson - 07-04-2015, 04:38 AM
RE: American Bosch 5AC - by Radioroslyn - 07-04-2015, 05:33 AM
RE: American Bosch 5AC - by dseverson - 07-04-2015, 02:24 PM
RE: American Bosch 5AC - by Radioroslyn - 07-04-2015, 05:10 PM
RE: American Bosch 5AC - by dseverson - 07-04-2015, 10:17 PM
RE: American Bosch 5AC - by Radioroslyn - 07-05-2015, 08:37 PM
RE: American Bosch 5AC - by dseverson - 07-05-2015, 10:07 PM
RE: American Bosch 5AC - by Radioroslyn - 07-05-2015, 10:26 PM
RE: American Bosch 5AC - by dseverson - 07-06-2015, 12:13 PM
RE: American Bosch 5AC - by jerryhawthorne - 07-06-2015, 12:51 PM
RE: American Bosch 5AC - by dseverson - 08-07-2015, 04:27 AM
RE: American Bosch 5AC - by Radioroslyn - 08-09-2015, 08:21 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 1910 online users. [Complete List]
» 1 Member(s) | 1909 Guest(s)
Avatar

>