1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
capacitor crossreference
Jim Berg
Member
***
Posts: 59
Threads: 2
Joined: Oct 2008
#15

02-18-2009, 03:11 PM
Radio Shack around here was kind of handy to have, but closed due to the economy. The owner was a ham, and two of the ladies that worked there worked at the stove factory when I was working there. They would show you where the resistors, caps and other parts were. No blank stare. Sorry to see them close, as next nearest is another 25 miles away.
Find
« Next Oldest | Next Newest »


Messages In This Thread
capacitor crossreference - by Howard Stricklin - 02-15-2009, 02:22 PM
Re: capacitor crossreference - by Syl - 02-15-2009, 03:27 PM
Re: capacitor crossreference - by AI2V - 02-15-2009, 03:36 PM
Re: capacitor crossreference - by Syl - 02-16-2009, 12:35 AM
Re: capacitor crossreference - by codefox1 - 02-16-2009, 07:02 PM
Re: capacitor crossreference - by Syl - 02-17-2009, 08:07 PM
Re: capacitor crossreference - by gary rabbitt - 02-17-2009, 08:23 PM
Re: capacitor crossreference - by Syl - 02-18-2009, 12:33 AM
Re: capacitor crossreference - by FStephenMasek - 02-18-2009, 01:59 AM
Re: capacitor crossreference - by Jim Berg - 02-18-2009, 03:11 PM
Re: capacitor crossreference - by gary rabbitt - 02-22-2009, 04:42 PM
Re: capacitor crossreference - by gary rabbitt - 03-05-2009, 01:43 AM
Re: capacitor crossreference - by Ron Ramirez - 03-09-2009, 09:05 PM
Re: capacitor crossreference - by Ron Ramirez - 09-23-2009, 09:37 AM
Re: capacitor crossreference - by Ron Ramirez - 09-23-2009, 03:39 PM
Re: capacitor crossreference - by Raleigh - 10-03-2009, 01:22 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently 5467 online users. [Complete List]
» 1 Member(s) | 5466 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration