1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 40-180 tone control?
sdradioman
Member
***
Posts: 112
Threads: 36
Joined: May 2015
City: Brandon, SD
#5

07-14-2015, 07:57 AM
Yep, that's how it was when I started and that was how I recapped it but the tone doesn't change. I think I may have a bad pot then. I have a spare that I will swop out and see it that changes anything. Thanks for the picture!
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 40-180 tone control? - by sdradioman - 07-13-2015, 12:01 AM
RE: Philco 40-180 tone control? - by Nick3092 - 07-13-2015, 10:42 AM
RE: Philco 40-180 tone control? - by sdradioman - 07-13-2015, 09:58 PM
RE: Philco 40-180 tone control? - by Nick3092 - 07-13-2015, 11:55 PM
RE: Philco 40-180 tone control? - by sdradioman - 07-14-2015, 07:57 AM
RE: Philco 40-180 tone control? - by sdradioman - 07-14-2015, 09:52 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM

[-]
Who's Online
There are currently 5047 online users. [Complete List]
» 1 Member(s) | 5046 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration