Rogers 10-12s finished

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Rogers 10-12s finished

KCMike
Phorum Expert

Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.

#11

07-17-2015, 06:12 PM

Good to hear they sound nice as they look. The clock might be a challenge to find. I'm sure someone on here can help you with how to build a power supply. Good luck.

Find

« Next Oldest | Next Newest »

Messages In This Thread

Rogers 10-12s finished - by Dan Walker - 07-16-2015, 09:38 PM

RE: Rogers 10-12s finished - by Eliot Ness - 07-16-2015, 10:29 PM

RE: Rogers 10-12s finished - by morzh - 07-16-2015, 10:47 PM

RE: Rogers 10-12s finished - by Fred Taylor - 07-16-2015, 11:44 PM

RE: Rogers 10-12s finished - by Dan Walker - 07-17-2015, 12:13 AM

RE: Rogers 10-12s finished - by Fred Taylor - 07-24-2015, 09:36 AM

RE: Rogers 10-12s finished - by Fred Taylor - 07-17-2015, 12:45 AM

RE: Rogers 10-12s finished - by PhilcoJohn - 07-17-2015, 07:15 AM

RE: Rogers 10-12s finished - by klondike98 - 07-17-2015, 11:22 AM

RE: Rogers 10-12s finished - by KCMike - 07-17-2015, 01:29 PM

RE: Rogers 10-12s finished - by Dan Walker - 07-17-2015, 04:39 PM

RE: Rogers 10-12s finished - by KCMike - 07-17-2015, 06:12 PM

RE: Rogers 10-12s finished - by Fred Taylor - 07-19-2015, 12:14 AM

RE: Rogers 10-12s finished - by Dan Walker - 07-19-2015, 09:07 AM

RE: Rogers 10-12s finished - by Paul Philco322 - 07-24-2015, 09:36 PM

RE: Rogers 10-12s finished - by Dan Walker - 07-26-2015, 08:03 PM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached. I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me