Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Persistance Pays Off!
#8

More good news with this radio. Tested the tubes and all were very good except the 7B8 tube which read a bit weak. Luckily, I had a better 'Genuine Philco' 7B8 in my stash to swap into the radio. I must say, these loktals are fairly durable tubes overall. Both dial bulbs are blown, but everything else checks out so far. One question I have is cleaning the slug tuners on these units. As I said earlier, it will tune some stations on low power, but it's VERY touchy and I am suspecting dirt and crap in the tuner. Is there a safe way to clean these or should I simply use compressed air to get the worst of the gunk out of the tuning coils and slugs?

No matter where you go, there you are.


Messages In This Thread
Persistance Pays Off! - by Jayce - 07-25-2015, 07:22 PM
RE: Persistance Pays Off! - by NostalgiaRadioTime - 07-25-2015, 09:07 PM
RE: Persistance Pays Off! - by Jayce - 07-25-2015, 09:16 PM
RE: Persistance Pays Off! - by NostalgiaRadioTime - 07-25-2015, 09:26 PM
RE: Persistance Pays Off! - by VntgRads - 07-25-2015, 09:53 PM
RE: Persistance Pays Off! - by Jayce - 07-25-2015, 10:06 PM
RE: Persistance Pays Off! - by Squire - 07-26-2015, 11:59 AM
RE: Persistance Pays Off! - by Jayce - 07-27-2015, 04:01 PM
RE: Persistance Pays Off! - by Scottb - 07-28-2015, 10:01 AM
RE: Persistance Pays Off! - by Arran - 07-29-2015, 06:26 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1898 online users. [Complete List]
» 2 Member(s) | 1896 Guest(s)
AvatarAvatar

>