Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Help with a Philco 89B
#18

Welcome to the phorum, Steve.  Your neck of the woods is on my bucket list to visit...someday.  In answer to your much earlier question about converting to a three wire line cord, yes, with this set you can connect the ground to chassis.  This is evident in your photo by the riveted ground clip on the back of the chassis to the right of the insulated antenna clip.  This is not always the case, but since it was intended to have a ground wire to earth you are really not changing anything.  The only possible disadvantage is that by grounding to the home wiring you could pick up "noise" from other equipment and appliances tied into the same ground network.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:07 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:34 PM
RE: Help with a Philco 89B - by Steve Davis - 07-26-2015, 05:11 PM
RE: Help with a Philco 89B - by morzh - 07-26-2015, 09:54 PM
RE: Help with a Philco 89B - by klondike98 - 07-26-2015, 10:02 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:44 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:59 AM
RE: Help with a Philco 89B - by morzh - 07-27-2015, 10:44 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:33 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:40 PM
RE: Help with a Philco 89B - by morzh - 07-27-2015, 03:14 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 05:42 PM
RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 02:51 AM
RE: Help with a Philco 89B - by sam - 07-28-2015, 03:00 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 05:18 AM
RE: Help with a Philco 89B - by morzh - 07-28-2015, 09:49 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 08:06 AM
RE: Help with a Philco 89B - by GarySP - 07-29-2015, 08:35 AM
RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 05:10 PM
RE: Help with a Philco 89B - by kiwi_steve - 08-01-2015, 07:48 PM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 12:16 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 01:11 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 02:27 AM
RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 08:54 PM
RE: Help with a Philco 89B - by kiwi_steve - 09-02-2015, 06:39 PM
RE: Help with a Philco 89B - by Arran - 09-03-2015, 01:03 AM
RE: Help with a Philco 89B - by kiwi_steve - 09-03-2015, 04:28 PM
RE: Help with a Philco 89B - by kiwi_steve - 09-22-2015, 05:18 PM
RE: Help with a Philco 89B - by kiwi_steve - 10-20-2015, 12:19 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently 2103 online users. [Complete List]
» 1 Member(s) | 2102 Guest(s)
Avatar

>