39-30 Refurb

Thread Rating:

1 Vote(s) - 2 Average
1
2
3
4
5

Linear Mode

39-30 Refurb

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#12

07-30-2015, 07:52 PM

Hi Nick,

<So, I think that means I can say for sure the audio stage, tone controls, and speaker are not causing the issue. So now I'm left trying to figure out what in the earlier stages is causing some kind of distortion that is being filtered out on the "no bass" setting, but comes through on the other 2 settings.

If I'm reading your previous paragraph correctly your issue could be in the 1st audio stage. So you know the drill check plate,grid, and cathode voltage for anything that seem hi or low.
Check 31 to see if it is open, 32 gone high, replace 34 for the heck of it.

GL
Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

39-30 Refurb - by Nick3092 - 05-13-2015, 10:32 PM

RE: 39-30 Refurb - by Radioroslyn - 05-14-2015, 06:25 AM

RE: 39-30 Refurb - by Nick3092 - 05-14-2015, 09:17 AM

RE: 39-30 Refurb - by morzh - 05-14-2015, 09:53 AM

RE: 39-30 Refurb - by Nick3092 - 05-14-2015, 10:56 AM

RE: 39-30 Refurb - by Nick3092 - 05-14-2015, 06:58 PM

RE: 39-30 Refurb - by Nick3092 - 05-14-2015, 10:58 PM

RE: 39-30 Refurb - by Nick3092 - 05-15-2015, 08:24 AM

RE: 39-30 Refurb - by morzh - 05-15-2015, 01:56 PM

RE: 39-30 Refurb - by Nick3092 - 05-24-2015, 09:33 PM

RE: 39-30 Refurb - by Nick3092 - 07-30-2015, 07:31 PM

RE: 39-30 Refurb - by Radioroslyn - 07-30-2015, 07:52 PM

RE: 39-30 Refurb - by Warren - 07-30-2015, 08:37 PM

RE: 39-30 Refurb - by Nick3092 - 07-31-2015, 08:19 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

Who's Online

There are currently 5525 online users. [Complete List]
» 1 Member(s) | 5524 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me