1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
AES power supply kit mods?
ccomer1955
Senior Member
****
Posts: 264
Threads: 51
Joined: Aug 2014
City: San Antonio, TX
#6

07-31-2015, 01:40 PM
The LED works perfectly hooked up as you described. I also have a small fan that I'd like to place on the box directly in front of the A voltage regulator's heat sink. The fan is 12 volts and 0.06 amps. Will a 1 watt 300 ohm resistor work across the second secondary (28v at 20ma) to bring the voltage and amperage down enough for the fan?
Charlie in San Antonio
(This post was last modified: 07-31-2015, 01:52 PM by ccomer1955.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
AES power supply kit mods? - by ccomer1955 - 07-23-2015, 12:49 PM
RE: AES power supply kit mods? - by morzh - 07-23-2015, 02:50 PM
RE: AES power supply kit mods? - by ccomer1955 - 07-23-2015, 06:05 PM
RE: AES power supply kit mods? - by ccomer1955 - 07-30-2015, 10:17 PM
RE: AES power supply kit mods? - by morzh - 07-31-2015, 10:41 AM
RE: AES power supply kit mods? - by ccomer1955 - 07-31-2015, 01:40 PM
RE: AES power supply kit mods? - by morzh - 07-31-2015, 02:30 PM
RE: AES power supply kit mods? - by ccomer1955 - 07-31-2015, 10:02 PM
RE: AES power supply kit mods? - by morzh - 07-31-2015, 10:09 PM
RE: AES power supply kit mods? - by ccomer1955 - 08-01-2015, 03:00 PM
RE: AES power supply kit mods? - by ccomer1955 - 08-02-2015, 02:06 PM
RE: AES power supply kit mods? - by morzh - 08-02-2015, 04:35 PM
RE: AES power supply kit mods? - by Arran - 08-04-2015, 05:56 AM
RE: AES power supply kit mods? - by Raleigh - 09-02-2015, 09:06 PM
RE: AES power supply kit mods? - by ccomer1955 - 09-02-2015, 10:22 PM
RE: AES power supply kit mods? - by Raleigh - 09-03-2015, 06:14 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)